Blood Sample Collector With Blood Extraction Needle Aseptic S-3 Storage Of Specimens

Blood Sample Collector With Blood Extraction Needle Aseptic S-3 Storage Of Specimens

Structure Composition

Disposable human arterial blood sample collector (hereinafter referred to as collector) S-3 includes sample clip, pull rod, piston, piston exhaust valve, seal, blood sample needle, needle cover and cubic plastic block. D-3 consists of a sampling rod, pull rod, piston, piston vent valve, seal, blood needle, needle and button ring.

Objective

• Arterial blood gas analysis provides an objective indication of the nature and extent of dysfunction and is the best way to determine whether hypoxemia or carbon dioxide retention is present.
• Guidelines for the coordination of oxygen therapy and mechanical ventilation parameters.
• Arterial management in the emergency room.

Scope Of Application

Collection and preservation of arterial blood samples. Blood samples collected can be used for blood gas analysis

Storage Of Specimens

• Our blood contains respiratory active cells (such as white blood cells and reticulocytes) that continue to consume oxygen to produce CO2 after sampling. When normal arterial blood samples were stored in vitro at 37℃, PACO 2 increased by 1 mm Hg every 10 minutes and pH decreased by 0.01. Therefore, blood must be sent for examination immediately after blood collection. In general, the time from sampling to testing completion should not exceed 30 minutes.

• 
  

  In case of special circumstances, it cannot be confirmed immediately, it should be stored in ice water container or refrigerator, but the storage time should not exceed 2 hours. Please wait a few minutes at room temperature before measuring. 0.014, PaO2 and PaCO2 also affect pH value with temperature increasing 1℃.

  
  

Usage Method

1. Human artery was selected and disposable blood collector of human artery was taken out.
2. Pull the rod to the blood volume position for precollection.
3. Pull out the needle, pass it through the artery, and the blood comes out naturally.
4. When arterial blood reaches the preset position, the piston discharge valve closes when wet and pulls the blood collector.
5. Activate the safety device (insert the needle into the plastic cube to avoid squeezing the sheath or accidental puncture) and remove the needle.
6. Tighten the seal and leave for testing.

Precautions, Warnings and Suggestive Instructions

1. abandon
2. If the container is open or damaged, do not use the contents.
3. The use of the product should comply with the requirements of the relevant operating procedures of the medical department.
4. In the process of using the product, it should be carried out slowly to avoid pain caused by excessive exertion.
5. Discard infected waste after use.

Warning

• They need to collect blood samples for use. Be careful when using blood samples and devices. Please wear qualified rubber gloves to avoid direct contact with blood. Aseptic technique should be used throughout blood collection to prevent infection of blood collection site.
• If there are any bubbles in the collector, remove them immediately and seal the sampler.
• Flip the collector over several times, then rotate the palm back and forth several times to mix the blood evenly.
• Do not store blood samples or reduce storage time. If immediate testing is not possible, it should be stored in a refrigerator at 4°C and blood samples should be tested within 30 minutes of taking blood

Company profile

Zhongxiu Science And Technology Co.,Ltd., is a high-tech enterprise engaged in the research and development, production and operation of in vitro diagnostic products. The in vitro diagnostic products developed by the company cover POCT series, microbial series, biochemical series and immune series reagents and supporting instruments.
The company has always adhered to the core concept of "fast and accurate, living up to life", committed to providing society with excellent products and services, and contributing to the cause of human health.

Zhongxiu Science And Technology Co.,Ltd., founded in 2016, is located in Dingluan Industrial Zone, Changyuan City, Henan Province. The company covers an area of about 100 acres and the initial investment is about 200 million yuan. The company has a scientific and complete management system, a purification workshop of national standards, and a fully functional inspection center. On this basis, the company will continue to invest in research and development, accumulate technical strength, update manufacturing equipment, improve production technology, improve inspection technology, improve product quality, and provide customers with safe and effective in vitro diagnostic products.

Zhongxiu Science And Technology Co., Ltd. is a high-tech enterprise engaged in the research and development, production and operation of in vitro diagnostic products. The in vitro diagnostic products developed by the company cover POCT series, immune series, microbial series and other reagents and supporting instruments.

The company has always adhered to the core concept of “fast and accurate, living up to life”, committed to providing society with excellent products and services, and contributing to the cause of human health.